The service wasn’t especially cheap but it has turned the bike into a usable machine which it wasn’t really before and in my view it wasn’t just money well spent, it was vital.

The Italian trip was a fantastic experience and an excellent test of both bike and rider. Apart from the duff hand, I think both came through it fairly well. The GS was very pleasing, coping with both the long trip there and back (1200 miles each way of mixed motorway stuff and country roads through very hilly areas with lots of switch-backs and the like) and the off-road riding in the mountains with generally, deep, big and sharp gravel plus many very tight turns.

SIDESTAND MOD.

The thing that got my attention mostly was the dismal side-stand on the GS which, especially when travelling heavily loaded, had the bike leaning over much too far, to the point of being sufficiently unstable as to fall over at the slightest opportunity.

I had noticed this before I set off an had cobbled together a block of wood some 4 cm. thick, zip-tied to the side-stand. This helped in keeping the bike upright but was hell to deploy as it required leaning the bike over a substantial amount in the wrong direction to sweep the stand down and forwards to the point it was in position to support the bike. On my return I solved the problem partially by spotting a bit of weld metal at the point on the stand where it is stopped against the attachment for the stand on the bike. This had the merit of stopping the stand from swing too far forwards and as a consequence, it holds the bike more upright. I also ground off the leading edge of the stand where it had previously fouled the ground in its arc. This helped by reducing the amount needed to hold the bike off the vertical when deploying it.

FORKS

The bike needed a huge amount of cleaning after the trip and I decided to move/remove various bits of bike to facilitate this process. One thing I wanted to do was to have a look at the forks to check that no corrosion was taking place under the clamps (as this was a potential problem I had read about some folk having) so I removed them, discovering in the process that the left hand fork stanchion was badly scored around its circumference at the point where it is held by the lower fork bridge (triple clamp), making it very hard to remove and to adjust up and down in the triple clamp – even after wedging the opening in the clamp wider. I cleaned up the scoring and read the service manual on the subject of forks, which made it clear that they had always been set wrongly. As delivered to me, the top of the forks was flush with the triple clamp rather than being set 7.8 mm. above it as specified. I set the forks at the specified height and although the difference is hardly discernible, it does feel that the steering is a little quicker as one might expect.

I complained to the dealer I bought the bike from (South London Motorrad) about this state of affairs (Mainly the scoring on the stanchion tube) but they were less than interested and despite me telling them that I thought the fork was potentially unsafe, and a candidate for a warranty claim (on the grounds that if they hadn’t caused the damage to the fork, it must have been BMW at the time of manufacture). They took a few photos and said they would contact BMW and revert to me but of course I have heard nothing. My conclusion, after this incident and the two previous things that upset me badly about their servicing (jobs not done, wheel bearings not checked), is that SOUTH LONDON MOTORRAD servicing is very poor, the staff are unreliable and I recommend you don’t go near them.

Mainly as a consequence of my unhappiness with SLM, I discovered Mark Holden, who runs an independent, and very reliable, friendly and helpful service workshop in Bromley High Street. He has now done a number of things on my bikes (the GS and the TTR and I have nothing but praise for his approach, speed and standard of workmanship.

It was Mark who put me in touch with HM Racing at Green Street Green where Perry Leask, a many times national motocross champ works on bike suspension for race teams, individuals etc. Currently as a later post will mention, he is scheduled to work on my TTR.

In removing the rear wheel I found that in practice it was unnecessary to slacken off the chain tensioner adjusters as there was sufficient play to remove the wheel without slackening them. I learnt that a bit of lubricant makes the job much easier and that KY jelly does the job very well. Not a lot is needed so a smallish tube of it is sufficient. I noticed a bit of a tear in the inner tube close to the valve stem. I don’t know if I was responsible for this or someone else. However, the tyre did hold pressure OK. I pumped it up using my new cyclepump for which I soldered up a connection enabling me to use a battery connected fly lead usually used for my heated jacket.

At the last service with South London Mottorad, the rear wheel bearings were replaced as they had started to collapse – great for ony 5000 miles! I asked SLM to carefully check the front wheel bearings as I wanted to be sure they would be OK for the Slovenia trip. SLM told nme they were fine. However, on removing the front wheel it was clear they had not removed the wheel themselves and I could feel a distinct roughness in the bearings which also felt as though there was no grease in them. I am very disappointed in SLM – things have gone downhill since the takeover. However, I am coming to value Mark Holden more and more – he is a super guy to do business with and really knows his stuff. As an independent, he s also a lot cheaper than the BMW dealerships! Mark will be replacing the front wheel bearings for me and altough it won’t be paid for under warranty, I am confident I’ll get a better job and we’ll use SKF bearings rather than some no-name Taiwanese things.

Things seemed pretty good. I had the covers off the starter and rotor to check the starter gears for wear but couldn’t see any so that relieved me from worrying bout the slight noise the bike makes when switching it off – something I had been concerned might indicate wear in the sprag clutch. The rear brake pads looked as thought they could do with replacing so I ordered both front and back sets from Moto-Ward which arrived by post on Thursday. The day before, I had received another item – a bike lift with which I can lift all three bikes clear of the ground. With the TTR I can do it single handed but with the other two bikes, I need help. I steady the bike whilst dearly beloved pumps up the bike lift. Thus on Thursday, I was in good shape to change the brake pads, a task that proved very easy. I also got to test the alloy tyre lever cum ring spanner I had bought for the F800 as the rear wheel nut is the same 24mm size. The alloy lever had no trouble undoing the nut and appeared to suffer no distortion in the process – so perhaps it was worth the rather high price.

Yesterday, I was keen to bed the new pads in so went for a ride around the neighbourhood, taking in a few unsurfaced roads – they led me to think the front forks could do with some attention but I shall await the first real offroad experience (planned for the coming Sunday)  before fiddling with them. All was going well until on the way home, a van did a u-turn in front of me with signaling. I slammed on the brakes but the front wheel locked and I went down hard. The van driver did at least show concern and claimed he ws a biker and said he had signalled – frankly I don’t think so. In any event, I managed to ride home OK but with a very sore hand, knee and ribs. It was the hand that hurt most and X-rays taken later at the A&E department of our local hospital showed I had broken my little finger. This was strapped up to a splint and I was sent on my not very merry way.

It has put paid to my weekend plans for sure. No doubt if I was 20 years old and a MotoGP star, I’d be out on the track ignoring the pains in hand, chest and knee and just getting on with the job – unfortunately anno domini has decreed that ain’t gonna happen. I just hope I’m back in shape for my next Wales trip planned for the middle of next month.

The design is pretty basic – air-cooled, carburetted with no fancy electronics, just what one needs if a bike has to be fixed in the middle of nowhere! Thus far I have adjusted a few things here and there, topped up the brake fluid front and rear (the pads need changing but as it’s Easter, I can’t order new ones before tomorrow. I had a side cover off to look at the starter motor shaft and idler gears (these can wear badly once the sprag clutch gets worn apparently) but everything looked pretty good to my relief. I have not adjusted any suspension settings and will wait until I’ve had my first off-road experience before touching them.

On the 100 mile ride home with the new machine, it managed 55-60mph on the motorway fairly readily so it will be good for getting to local trails not too far away. For going further afield, I shall be getting a trailer however as I don’t fancy riding all the way to say North Wales on this bike. Apart from anything else the seat is hard on the bum! I am going to try fitting the Airhawk to it for the ride down to Wiltshire and back. I can stuff it in my rucksack when actually riding the trails.

Whilst chatting to the sales folk, they asked if I had had the top radiator hose recall done. I knew there was one in progress but I hadn’t had it done as I had had no word from South London Motorrad.  Bahnstormer offered to do it there and then and having time on my hands I said “Great, please go ahead”. When they entered the registration in the BMW database, it seemed that there was a bunch of other recall type work to do. This puzzled me as SLM were supposed to have done it already (re-routing the ABS lines for instance) but they also did that for me so apart form some monster firmware update (this would apparently have taken 2 hours and it’s seemingly to addess a stalling issue which fortunately, I don’t seem to have)  I am OK as far as BMW mandated fixes are concerned. I was pleased that Bahnsromer had shown such initiative and am only sorry that its really too far away for regular servicing.

On the ride home, I was very conscious of the AirHawk under my backside. I think there is probably a little too much air in it as I seem to wobble from side to side on it quite a lot. It also seemt to tip me forwards somewhat so at present, I am not a huge fan of it. No doubt I shall get used to it in time but will need a much longer run to determine its worth as an aid to stopping numb bum syndrome.

Doble’s unfortunately don’t operate on quite that principle – a service for free -  and as the 12,000 mile service is a major one for the Wing, I can expect a big bill However, I see from a recent flyer that they are offering 25% discount on everything apart from bikes over the coming weekend. The trouble is I don’t really need anything from them at present and a 25% discount isn’t enough to persuade me to buy stuff that I don’t need. Although, having said that, there is quite a decent range of Honda branded clothing (Joe Rocket stuff in actuality) that includes a Goldwing jacket that would look better on the bike than the BMW Rallye 2 Pro jacket I often wear..

Not unnaturally, I have not noticed any difference as the bike was running fine beforehand anyway. What I did notice was just how different the 650 GS loan bike I used felt (I had to leave my bike there for most of the day, and I needed transport). It seemed very low in the seat, rather underpowered, or at least lacking in the torque department and contrary to my expectations, the steering seemed very slow and the bike reluctant to tip in at corners. I didn`t check the tyres closely but they were road tyres, not TKC`s like mine – how much and what kind of difference this makes, I don`t know. I do know that I vastly preferred my own bike to the 650. Perhaps this had more to do with familiarity than anything else but the difference surprised me, I had thought the two bikes would feel much the same.

The weather was absolutely dreary and in the morning, cold with it. The heated hand grips are great but particularly my thumbs get cold even with them on. I guess it`s time to don winter wear.

8000 miles isn’t a huge amount for a year’s biking but to that I must add the mileage of my two foreign trips on other bikes (Patagonia 2700 miles, Italy at 1800 miles and a further 1000 miles for the GS) and we end up with a respectable total of 13,500 miles for the year. Not surprising that my woodwork has taken a back seat!

Tomorrow I am taking the bike to South London Motorcycles to get a set of knobblies fitted as on Saturday I shall be doing a bit of greenlaning – provided that the snow doesn’t come back in earnest..

I have ordered a set of tyre irons and a bead buddy – still neeed a bead breaker probably and a couple of other things, so I can change the tyres back and forth as I need. This is the best site I have found with advice on changing tyres on wheels like mine